Thursday, 20 February 2020

5 Different Types Of Adhesives To Use For Scale Modeling


If you have been building ship model kits for a while now, you most likely have your own tried and true adhesives and epoxies that have helped you finish your preferred projects. However, if you are a beginner, or you have turned out to be annoyed with your “go-to” adhesive, here is a quick breakdown of some of the available alternatives. The following are the five most common types of glues that can be effectively used for scale modeling:

1.       Epoxy Resin
It is a two-part adhesive that is made up of a paste and a hardener. Epoxy resins will attach more or less any type of two different surfaces jointly. Blending is needed prior to the application of epoxy resins, and drying time will normally be slower as compared to super glues, even though there are faster blends available. The final result is a very strong bond, even though the amalgamation of mixing, hardening time, and general mess means that it is far less usually used for building scale models.

2.       Cyanoacrylate or Super Glue (CA)
Super glue is an extensively utilized adhesive in the world of scale modeling. Whether it is joining metal to plastic or metal to metal, this adhesive comes out to be extremely useful. This glue has a tendency to set very quickly, so additional precaution is supposed to be taken at the time of lining up the components of ship model kits in order to keep away from a tricky fix afterward.
In addition, you need to be extra cautious to keep away from getting it on your skin because thumbs and fingers form a loving bond if you are not watchful.

3.       Canopy Glue
Canopy glue is most excellent for joining plastic to plastic. Such adhesives have the advantage of simple application and a clear finish – in other words, no nasty white spots after the glue has dried on the components of the scale model. Even though the bond is not super strong, however, it is a handy tool when it comes to building smaller scale models.

4.       Aliphatic Glue
Aliphatic glue is also known as wood glue and it is the same as PVA. However, this glue has a tendency to soak into joints better and a stronger bond is formed as a result. It even has a higher resistance to sand and water, and sets much faster as compared to PVA glue. As should be understandable by its generic name, aliphatic glue is just right for bonding wood to wood.

5.       Polyvinyl Acetate (PVA) Adhesive
PVA is one of the most popular commercial and domestic glues and it is based on water. This adhesive is normally best suited for landscaping or building dioramas, where it can be spread over a larger surface. Even though it has a weaker hold as compared to clear glues, it is very simple to use, reasonably priced alternative for building ship model kits. It is a perfect alternative when it comes to adding finer details to a display like stones or grass, and it is even quick to take away, if you do make any errors.

Thursday, 23 January 2020

Plank Tapering Guide For Scale Modeling


While working with the model boat kits, if you spend a few minutes with a piece of string or a tape measure and a ruler, you will soon see why it is essential to taper the planks to a narrower width at either one or both ends. When you measure the distance from the deck level to the bottom of the keel, around the outside of one of the midship frames, and then compare that measurement with the distance from the deck level to the bottom of the keel on a forward frame, there will be an obvious difference that can be noticed easily.

In simple theoretical terms, if the measurement at the third frame is 80mm and the fifth frame is 120mm then each plank needs to be narrowed down to 2/3 (80/120) of its full width at the third frame. By doing this the entire planks will arrive at the keel collectively. However, as per the experienced hobbyists, they always believe that the middle frames are the largest and it is at this part of the model that planks are at their full width. Towards the bow, they’ll require narrowing or tapering by an amount depending on the type of scale model you are working with.

In general terms, a bluff-bowed ship will need less tapering as compared to a sharp bowed vessel. It is possible that some sort of tapering will be needed as planks go towards the stern but it is even fairly possible that the distance, deck to the bottom of the keel, will be greater at the position of the last couple of frames than it is at midships. Where this is the scenario, the experts recommend putting in short triangular planks known as wedges or stealers.

When it comes to scale modeling, the 1st plank is generally started in one of the following positions:

ü  With a ship that has a straight or flush upper deck then the 1st plank is laid with its upper edge level with the deck surface. In some scenarios, it’ll have its top edge up to 5mm to 10mm under the deck level. Where this is performed, it is to make the construction of bulwarks easy at a later stage but in any case, it’ll be parallel to the line of the deck.

ü  In the case of models having the weather or upper deck in either 2 or 3 different sections, at differing levels, then the 1st plank is commonly run along the line of the main or middle deck then follows its natural course both aft and fore. There are quite a few modes that simply fall into this category.

ü  A lot of model boat kits that feature below deck open gunports necessitate that the initial plank follow the line of the gunports and it’ll run right away below or above a row of gunports.
When you’ve recognized the position of the initial plank, join it into position using the PVA glue and without any tapering. Ensure that both planks follow the same line and are a mirror image of each one another.

Thursday, 2 January 2020

A Guide To Weathering Ship Model Kits

There is nothing quite like shiny, newly-finished ship model kits and there is a real sense of achievement when it is all put together. However, even though some scale models look wonderful with a clean coat of paint, others benefit from a more aged, authentic look to a great extent. This is where weathering comes in, and with a few choice methods, a finished scale model can be converted into a realistic duplication of the actual thing.

The following are a few weathering tips that you need to keep in mind:

Beginning weathering
As with the entire range of scale models, having good reference material is a good place to begin with. Things such as age, environment, shape, construction, and level of maintenance will have an effect on the way the scale model is supposed to be weathered. As an instance, water will run down or even pool on a scale model to cause rusting. Some scale models can rust right through, while more robust, armored scale models have a tendency to just demonstrate surface rust.
Ship Model Kits


Some aluminum scale models do not rust at all. The majority of them get regular maintenance, but some normally necessitate the least maintenance and are rather exposed to higher degrees of wear and tear. The sequence in which you weather is significant for attaining the most genuine, realistic results.
Before you begin weathering the scale model, you are supposed to initially get rid of any residue or grease, apply the selected color of paint, and add any decals. If you simply are determined to add a coat of dust, paint every detail in advance. However, if you are planning a more detailed weathering job, it may be easier to paint the details as you go.

With the intention of accomplishing the most genuine and realistic outcomes, the array in which you weather plays a crucial role. Beginning with a ‘factory finished’ vehicle, begin by breaking down the color. After that, apply wear and exposure effects to the paintwork. Continue by drawing attention to any metallic effects where paint has worn through, and finish by showcasing exposed metal for areas that have taken the highest level of wear.

Weathering military ships
There are several types of military ships that usually go through a higher amount of wear and tear as compared to other ships. If you are working on a military ship scale model, there are a few things that you can take into account to achieve that weathered finish.

Ship Model Kits


As ships age, they turn out to be discolored and dirty. With the aim of breaking down a factory-finish, just apply washes of white, burnt umber and pale yellow oil paint to the ship scale model in no specific sequence, judging by the changing affect how much to put on.

The experts for scale modeling working with a variety of ship model kits always recommend that muddy water splashes can be suggested using pale, almost white streaks. You can always abide by the things mentioned above in order to give your scale model a wonderful weathered look!

Thursday, 12 December 2019

All About Cleaning An Airbrush For Model Boat Kits

An airbrush is one of the types of equipments used by professional hobbyists while building model boat kits in order to give the finished more an immaculate feel and finish. An airbrush is mechanical equipment in which the air and the paint are combined together internally. When the button is pushed down, the air is passed through the nozzle and the paint is diffused on the components of the scale model. This leads to a lot more superior atomization, and allows you to create perfect, even patterns.

With the help of minor tuning to either the supply of paint or air, you can create a huge range of amazing effects effortlessly. By swapping out the needle of the paint, you can add even more assortment to the patterns for paint spray, making this an extremely useful tool if you have a little bit of innovative stylishness.

So, before we come to the ways to clean an airbrush, you will need to select the kind of airbrush. The following are the two basic types of airbrushes available for scale modeling:
ü  Single Action Airbrush

ü  Dual Action Airbrush

How to clean an airbrush
When the paint brush is dirty, it comes out to be very difficult to carry out flawless work, and an airbrush is precisely the same. Even very little amounts of dry paint can have an effect or slow down the performance of the airbrush while working with any of the model boat kits. So, make sure the equipment is cleaned properly right after every use.
Always make use of a tissue paper or a rag for the purpose of getting rid of the reservoir and then half-fill it with the thinner. The thinner must be blown through the airbrush until there are no noticeable particles of the paint. Hold a tissue paper or a rag over the needle of the paint to compel the air back into the reservoir, and allow it to bubble back to clean the entire passages. Always bear in mind to keep away from standing the needle on its point because this causes it to bend.
After it has been used a little bit, strip down the airbrush and drench the head and the needle in thinner for the night. Keep away from standing the needle on its tip for the reason that it can make it twist and, at times, it can even break down.
Repairing a twisted needle of an airbrush
The needle must be held against a leveled surface at the angle of the point, run the fingernail across the point at the same time as revolving the needle.
So, are you also in search of a new airbrush to complete your scale model? You can always take references and professional help from the experts in the industry or can even consider approaching a local hobby store. No matter what sort of model boat kits you are working with, with the help of a right airbrush, you can transform the overall finish of the scale model tremendously!

Friday, 25 October 2019

Essentials To Choose A Wooden Boat Model Kit


Getting one of the best wooden model boat kits is essential for every scale modeler. Whoever, when it comes to selecting one amongst a variety of them available on the market, you must keep the following things in mind:

ü  The type of hull
Several kinds of the hull may be more at ease for beginners as well. Even though a solid hull has fewer components to put together, however, it actually confines what you can put up. Plank on bulkhead models are a bit more complex. This is most likely one of the most general kind of scale models to build. Although they are still in the realm of beginners, however, they will necessitate more work. You are going to have a lot of alternatives with this sort of hull.
Plank on frame models are the most minimal. You have got to build the whole thing essentially from the bones. It has a more practical frame and keel, something very similar to an actual ship.

ü  Instructions in the kit
The instructions are vital for the reason that these are not only snap-in plastic components. You have to make the majority of the components on our own. Especially, if you are a novice, this can be overpowering if the instructions are not understandable. Instructions differ between retailers for the reason that a lot of the model boat kits are designed by a person under contract. They may or may not have experience writing instructions for beginners.

An approach to check if the instructions are clear enough for you is to carry out a search online and read them prior to you make a decision to buy a specific scale model. Some of the kits even consist of a practicum, which is a quick course-like walkthrough. They can help guide you through the details of building the ship prior to ever actually pick up any of the components.

Most important of all, a list of numbered components is supposed to be included, so you know for sure that you’ve got everything you need before you get halfway through and understand something is missing.

ü  The cost of the kit
The last but not the least aspect to mull over is the amount you are ready to shell out. A few kits can be prohibitively costly. If you are an experienced hobbyist, the expense may be worth it. However, being a novice, you do not wish to be trapped with a model you have sunk a lot of money into. That said, at times, the more money you shell out, the better quality components you get. You are required to balance the price with the quality so that you are expected to complete the build as a result of quality components but not so trapped in the money factor that it is not entertaining any longer.
Without any doubt, building model boat kits is a brilliant hobby, but it calls for patience and coordination of hands and eyes. If you think you are ready for all that, it is the right time to get a quality scale model for you.

Friday, 27 September 2019

General Instructions While Using Glue To Join Model Kit Components


If you would like the surfaces of the ship model kits you stick together to have strong bonds, it is necessary that you abide by the general guidelines that are mentioned below. However, if you do not succeed to abide by them, you are most likely to have fragile bonds, which can be wasteful.

ü  You are supposed to clean the surface prior to the glue is required to be applied. It is necessary that you comprehensively clean the surface before making use of the glue. You are supposed to clean the surface to be free of things such as loose particles, grease, and dirt. If you apply the adhesive with these on the surface, then it may not be as effective in joining the two surfaces.

ü  Then try roughing up the surface. This is not mandatory since it just applies at the time of employing the adhesives that have a label showing that you are supposed to be employing them with rough surfaces. You may make use of sandpape3r in order to rough up the surface. The surface should be cleaned when you’re done. This step is very important because roughing will add to the surface area of the component that’s in contact with the adhesive, therefore, in the end, enhances the bond strength between the two components you’re putting together.

ü  Clamping time is when you either hold the components ship model kits collectively or leave them as they dry up. If you’ve got any needless interruptions, then the bond of the components is expected to be less durable and weak.

ü  You are supposed to control your impatience. Even though this sounds simple to do, however, you may quickly fall prey and start making use of things prior to they’re completely cured. If you do this, then you’ll make the bond less durable because it won’t have been strong enough the moment you use before the components you join together being completely cured.

Issues with adhesives

Plastic sorts of cement may often not bond surfaces that have paint. This is for the reason that they’re for use mostly with plastics. However, you can scratch away a little color from the surface you would like to join together and apply adhesive on the spots to join together. This allows the cement to bond together effectively.

You may get rid of the adhesive from the surfaces you don’t desire it by rubbing it using a soft cloth. However, if they’re more, you may use a brilliant rubbing compound such as a tube of toothpaste. On the other hand, you may make use of a polishing kit. If it is a pure fog then model wax, liquid acrylic floor wax or clear enamel can help you to get rid of it.

You should make use of the adhesives in places with adequate ventilation. In case you inhale the vapor, take proper care since they direct in their packaging materials. Keeping the instructions mentioned above while working with ship model kits will make sure you come up with a durable scale model!

Thursday, 22 August 2019

Steps To Build Deck Rope Coils

Deck rope coils are one of the slight additional details that make the deck of the ship model kits stand out. The following are a few steps that will help you get the job done right the first time:

Ø  Double-sided tape, scrap wood and brass. Sizes are controlled by what you have in the scrap boxes.

Ø  A piece of plywood is glued to 25mm dowel, then apply a piece of tape to the surface of the ply.

Ø  Drill a hole in the base of the scrap timber to a depth of around 20 mm to accompany the brass sleeve. Load the table top into the sleeve. The top piece will now be capable of spinning in the completed jig.

Ø  Choose the required gauge and color of rigging cord for the job.

Ø  Pull the cord through the bees wax to obtain maximum control of the cord.

Ø  Ready the tape by taking away the protective coat.

Ø  Mark the center of the top and begin coiling the end of the cord, applying light pressure that will keep the cord under control.

Ø  The technique is to turn coil and add pressure to the top as you go. It is at this point that you decide what diameter you require for the job.

Ø  Apply white PVA wood glue and rub in so as to cover the coil.

Ø  Drying time of ship model kits is supposed to be roughly none hour. Test as you go, or apply heat lights if required.

Ø  Once the coiled rope is dry, do away with the piece with a flat blade ready for installation.

Ø  Make use of PVA wood glue in order to join the piece and clean up where required.

Capstan Bars & Handspikes
These are essential equipment on the majority of scale models and if they are loose and not connected to the windlass or capstan then the holes in the windlass and the capstan to house these bars are supposed to be square. If the capstan bar is installed in the capstan, each bar is supposed to be around 1/3 the beam of the ship.

Windlass
A winch, particularly one on a ship, the windlass is an apparatus for moving heavy weights. Usually, a windlass consists of a horizontal cylinder supported between cheeks at each end, it is rotated by the turn of a handspike inserted into the barrel. On a ship it is usually octagonal in shape to stop slippage, it even generally consists of a pinion and gear system to gain benefit with heavier loads. As a result of limited space on a ship, and as one man could merely turn the drum by a quarter of a turn per pull, the use was discontinued for bigger ships with heavy loads to shift.
No matter what part of the ship model kits you are working with, always keep in mind that you need to concentrate on it to ensure it has been joined properly and will not come out at any time in the future.